EL60N

Main characteristics

  • Electrolysis type: PEM (Proton exchange membrane, caustic free)
  • Number of cell stacks: 2

Hydrogen gas production

  • Max. nominal hydrogen flow: 63.3 Nm3/h
  • Hydrogen flow range: 10 -100%
  • Operating pressure: 15 – 40 barg (217-580 psig)
  • Hydrogen purity (before gas purification): > 99.9%; < 25 ppm O2; H2O saturated
  • Hydrogen purity (after gas purification): 99.999%; < 5 ppm O2; < 5 ppm H2O

Electrical requirements

  • Voltage: 3 x 400 VAC ± 10% (3Ph+N) / 3 x 480 VAC ± 10% (3Ph+N)
  • Frequency: 50 Hz ± 5% / 60 Hz ± 3%
  • Power (BoP + Stack):  329.2 kW
  • Stack consumption: 4.7 kWh/Nm3 H2
  • AC power consumption (BoP + stack): 5.2 kWh/Nm3 H2

Feed water – tap water (if water treatment plant is included)

  • Consumption: 90.4 L/hr
  • Conductivity: < 2,000 uS/cm (T 25 ºC (77 ºF))
  • Pressure: 2-6 barg (29-87 psig)
  • Temperature: +5 ºC to + 40 ºC (+41 ºF to +104 ºF)

Feed water – demi water (if water treatment plant is not included)

  • Consumption: < 1 L/Nm3 H2
  • Quality: > 10 MΩcm (< 0.1 uS/cm); TOC < 30 ppb

Control system

  • PLC: Fully automated and unattended with 15″ color touch screen
  • Communication: Modbus TCP/IP or Profinet (RJ45 port)

Environmental conditions

  • Ambient temperature range: +5 ºC to + 45 ºC (+41 ºF to +113 ºF)
  • Humidity: 0 to +95% (non-condensing)
  • Air ventilation: Available from a non-hazardous area
  • Installation area: Indoor/Outdoor

Dimensions and weight

  • Dimensions (LxWxH): 20 ft container (6.0m x 2.4m x 2.9m) (19.7ft x 7.9ft x 9.5ft)
  • Approx. weight: 13,000 kg (28,860 lb)

Standards & regulations

  • Compliance: CE, ISO 22734-1 / NFPA 2-2016 & NFPA 70

Other characteristics

  • Duty cycle: 100% (24/7)
  • Start-up time (from stand-by): < 1 sec
  • Cold start time: < 5 min
  • Nitrogen Supply System: For each purge, consumption is <0.2 kg at 3 barg (to be supplied by the customer)
  • Instrumentation air System: Consumption 7 Nm3/h at 10 barg (to be supplied by the customer)

Always included

All our products do always incorporate:

N

Hydrogen purification system (SAE J2719 September 2011)

N

Water treatment system

N

Hydrogen cooling system

N

Emergency shutdown system

N

Overpressure relief system

N

Redundancy on critical safety parameters

N

Uninterruptible power supply (UPS)

N

Hydrogen mass flow & hydrogen purity measure (H2O & O2 sensors)

N

Heat management (no cooling water is needed)

Additional Options

All our products can include:

L

Oxygen processing system

L

Instrumentation air system

L

Nitrogen system

L

Extreme environmental conditions package (low and high temp)

Products datasheet

Download